Did you know?

Refer to section "Removal of the EPA07 Temperature Sensors". Verify repair. 5. Monitor the DPF outlet pressure (pin 30) parameter. Is the DPF outlet pressure sensor voltage between 0.44 and 0.56 ... Remove the DOC inlet pressure sensor tube, hose and elbow. Refer to section "Removal of the EPA10 Diesel Oxidation Catalyst Inlet Pressure Sensor ...4. If present, check the condition of the insulation material around the exhaust pipe between the turbocharger and the ATD.. 5. Check the ATD mounting bands for tightness. If needed, tighten the mounting bands on horizon-tally and vertically mounted ATDs to 30 lbf·ft (41 N·m); on step-mounted ATDs, tighten the mount-ing bands to 15 lbf·ft (20 N·m).High DOC outlet temperature for DPF regeneration during the FTP cycle CAT 3126 engine. As seen in the chart, maintaining constant DOC outlet temperature at variable exhaust gas mass flow rate and variable DOC inlet temperature conditions is not a trivial task. Apr 15, 2018 · After it stopped my truck requested another park regen. If you’re needing that many regens, you may need a new filter or perhaps a sensor. You should go see your truck manufacturer. I should add that 200° is normal temp for your dash to show. Mine goes up to about 225° before the fan kicks in and brings it back down to 200°. COOLANT TEMPERATURE: 209F DOC INLET: 432F DPF INLET: 421F DPF OUTLET: 411F Last edited: Jun 10, 2017. 4vmach1, Jun 10, 2017. 4vmach1, Jun 10, 2017 #71 + Quote Reply. Trucking Jobs in 30 seconds. ... During one of the parked regen the delta-p set a out of range on the data monitoring, ...Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. 7. Perform a parked regeneration; during the regeneration, monitor (ASL: DOC Inlet Pressure). 8. During the parked regeneration, does either the DOC inlet pressure sensor drop to 0.0 psi at any time? a. Yes; replace the failed sensor. b. No; clear fault and release unit. The code likely occurred after extended idle and soot buildup has cleared ...Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. Active regeneration is usually not noticeable to the driver. The vehicle needs to be driven at speeds above 30 mph for approximately 20 to 30 minutes to complete a full regeneration. During regeneration, the exhaust gases reach temperatures above 1,000°F (550°C). Active regeneration is usually not noticeable to the driver. Ash LoadingMar 15, 2020 · The stage1 is before regeneration phase. The DOC inlet temperature, the DPF inlet temperature, and the DPF outlet temperature are sequentially lowered due to the heat loss. The stage2 is during regeneration phase. The DOC inlet temperature slightly reduces due to the vaporization heat of methanol. A) A forced regen will take approximately 40 minutes. It will cycle through 6 stages during this 40 minute period. If the Regen cycle takes longer than this, something else is still wrong. b) During a forced regen cycle, The DOC will get to about 550F, and the doser will activate, first, usually in short intervals, then come on solid.May 22, 2012 · The AFI wont kick in tell the DOC and DPF inlet temps reach 500+*f and the DOC temp must stabilize. Whats the turbo command %, turbo speed, boost pressure, EBP, and engine load during a regen? CAT Factory Trained & Cert. Heavy Equip+Truck Systems. 13. Inspect the DOC inlet pressure sensor electrical connector for corrosion and spread pins. a. If corrosion or damaged (or bent) pins are found, repair as necessary. Verify repairs. b. If no corrosion or damage is found, replace the DOC inlet pressure sensor. Refer to section "Removal of the GHG14 Diesel Oxidation Catalyst Inlet Temperature ...Exhaust Gas Temp 572, DOC Inlet Temp 572, DPF Outlet Gas Temp 1013 and still the REGEN process did not want to finish. The tech cleared my ash level to see if that would work and nothing. I got some recommended solutions, drop and burn the DPF / DOC, sensors, etc..Jan 15, 2017 · During an active regen, engine exhaust temp is slightly higher than normal but not significantly. Maybe 50 to 100 deg. F at best. The high temps are in the exhaust NOX/DPF filter. Everything upstream of that is pretty much normal from my observations. See this video on an entire active regeneration.

Ran an onboard filter cleanliness test to get the regen temps. Soot load was at 44%. Doc intake temp is 775 to 800. Dpf inlet is 1150 to 1185. Dpf outlet is 1220 to 1270. TC1TOP IS 1.5. EGR position is 35%. International is telling me its not eligible for the crankcase filter update, last 8 of vin: EL771725.a. If the DOC inlet pressure starts out above 10 kPa (1.45 psi) and decreases during a parked regen, this indicates that the DPFs were plugged and the parked regen has cleared them. Go to step 8. b. If the DOC inlet pressure starts above the pressure specified below and stays high, the DOC is considered plugged. Go to step 9. Table 1. Emissions ...DPF regeneration temperature rising strategy chiefly considers two temperatures including DOC inlet temperature and the DPF inlet temperature. Temperature rising approaches is based on Great Wall 4D83 diesel engine whose performance parameters are listed in Table 1 and DPF experiment system is shown in Fig. 8. Secondary post injection (Post ...Once the nozzle was cleaned out it would do the regen and the high soot level code went inactive. I'm working on an 08 Western Star with a 60 series Detroit with EGR and DPF. It is a 06R0998711 engine. It has an active 3719 High Soot Level code. The engine runs for about 2 minutes and then shuts down.

After it stopped my truck requested another park regen. If you’re needing that many regens, you may need a new filter or perhaps a sensor. You should go see your truck manufacturer. I should add that 200° is normal temp for your dash to show. Mine goes up to about 225° before the fan kicks in and brings it back down to 200°.There is always something . Excessive idling does cause the DPF to need a regen more often. The Pete I was in, it was recommended that if we had to idle due to temps, that we raise the idle to 1500 to help keep the DPF hot enough to regen itself. However, with the other issues you said it has, sounds like it needs to see Mr. Peterbilt.I began to run NED constantly while driving at work so I can monitor how the engine and regen process look like. Regens usually start at around 60% soot load, the percentage after regeneration goes down into low teens or low single single digits. From what I was able to observe, DOC usually gets somewhere in between 1050° and 1250°…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. My unit starts the regen but the DOC inlet temp is o. Possible cause: 3. If all sensors check out okay, perform a Low temp by disconnecting DEF metering uni.